đź› Number of components: 217 | Product: Milwaukee M18 Gas Cordless Band Saw | Time to Disassemble: 1 hours, 59 minutes

Milwaukee M18 Fuel Band Noticed

If you’re a plumber, electrician, or militant Do-it-yourself-er with a bunch of pipe to lower, Milwaukee’s cordless band saw is a gift from the instrument gods. It’s a beloved of contractors and resource renters for the reason that this noticed is as burly as they occur.

Electric power will come from a higher-velocity brushless motor that rotates the toothy metal band at 380 surface toes per minute. The 5×5-inch lower capacity is the most important you’ll obtain on a cordless band saw, enabling you to blast by means of huge pipes, thick fence posts, and steel bollards.

It’s also a lot less prone to breakdowns, thanks to a direct-push program that eliminates the want for a chain, a ingredient destined to extend and demand servicing. At 13.1 pounds, without the lithium-ion battery, the M18 isn’t the most portable or the easiest to carry, but there is no far better way to make clean, spark-free cuts by steel pipe.

How To Use a Band Saw

Searching for an excuse to acquire the mack-daddy of cordless band saws but just cannot justify it as a Do-it-yourself expenditure? With a hand pipe threader, a tap and die established, and the acceptable pipe and fittings, you can slash and fabricate industrial furniture for a pair hundred dollars—a lot considerably less than the $1,000+ value tag that substantial-finish industrial pipe home furniture commands on websites like Wayfair.

The route of the very least resistance would be to have Steve at The Home Depot minimize and thread the pipes for you, but Do it yourself chopping and threading offers you extra versatility (and less excursions back again to the keep when you get the measurements mistaken).

In advance of you embark on the pipe-based coffee desk or bookshelf of your goals, examine out these tips from Senior Test Editors Roy Berendsohn and Brad Ford to nail your favourite industrial pipe search.

Step 1: Degrease

Give the pipe and fittings a comprehensive cleansing with any degreaser or strong ammoniated cleaner in advance of you begin to sand you never want to spread the residual grease from the threading process. Denatured alcohol also works very well to split down the oil and clear off pipes—be careful, the threads can be quite sharp.

Phase 2: Scuff-Sand and Thoroughly clean

Sand the pipe and fittings with good sandpaper or so-called damp-dry paper (sandpaper that can be utilized with a reducing lubricant). You really don’t require just about anything significantly coarser than 120- or perhaps even 220-grit paper. The significant matter is to abrade off shiny places, rust, deep scratches, and the like. You can even use an ammoniated house cleaner in conjunction with moist-dry sandpaper although you’re executing this. Upcoming, use damp and clean paper towels to wipe down the pipe and dry the pipe comprehensively. Stick to with a person additional wipe making use of a solvent these kinds of as mineral spirits or liquor and a cleanse piece of paper towel or store towel.

Phase 3: Paint

Implement primer when painting metallic that has been abraded/cleaned, specially if there are bare spots or locations where by rust wanted to be eradicated. (Do not paint galvanized pipe with oil-based primers or paints that are identified as “alkyds.” Use paints that are termed “acrylics.” Normally, the paint will peel when exposed to humidity.) Use a single coat of spray metallic primer, adopted by at minimum two coats of major coat, which may be gloss enamel or satin enamel. Keep the can so that it’s not pointing right at what you want to paint. Push the can’s trigger and move about the object in a sweeping motion. As soon as the spray pattern clears the other finish, enable go of the button.

Alternatively, maintain the pipe’s industrial complete with a butcher’s wax coating. You may well have to reapply periodically to manage the complete, but it safeguards by now-rusting pipe from corroding more.


This article appeared in the November 2019 challenge of Preferred Mechanics. You can subscribe here.



Source website link